Lantronix UDS2100 Bedienungsanleitung

Part Number 900-448 Revision A September 2006 UDS2100 User Guide

2: Introduction UDS2100 User Guide 10 Figure 2-1. Serial Tunneling Example The Com Port Redirector software included on the product CD simplifies

2: Introduction UDS2100 User Guide 11 Protocol Support The UDS uses the Internet Protocol (IP) for network communications and the Transmission Cont

2: Introduction UDS2100 User Guide 12 Product Information Label The product information label on the underside of the unit contains the following

UDS2100 User Guide 13 33:: GGeettttiinngg SSttaarrtteedd This chapter describes how to get your UDS up and running in the shortest possible time

3: Getting Started UDS2100 User Guide 14 Installing the UDS Figure 3-1. UDS2100 Connected to Serial Device and Network To install the unit: To ins

3: Getting Started UDS2100 User Guide 15 Required Information Before configuring the UDS, have the following information available: Hardware Addr

3: Getting Started UDS2100 User Guide 16 Assigning the IP Address: DeviceInstaller This chapter covers the steps for getting the UDS2100 device ser

3: Getting Started UDS2100 User Guide 17 7. Select the device from the main window list and select Ping from the Tools menu. The Ping Device dialo

3: Getting Started UDS2100 User Guide 18 Table 3-1. Current Configuration Setting Description Name Configurable field. A name that identifies the

3: Getting Started UDS2100 User Guide 19 Setting Description Gateway Displays the UDS2100’s current gateway. To change the gateway, see Assigning

UDS2100 User Guide 2 Copyright & Trademark © 2006, Lantronix. All rights reserved. No part of the contents of this book may be transmitted or re

3: Getting Started UDS2100 User Guide 20 3. Continue with step 4 in 5: Configuration via Telnet or Serial Port (Setup Mode). Assigning the IP Addr

UDS2100 User Guide 21 44:: CCoonnffiigguurraattiioonn UUssiinngg WWeebb MMaannaaggeerr You must configure the unit so it can communicate on a n

4: Configuration Using Web Manager UDS2100 User Guide 22 Figure 4-1. Lantronix Web Manager The main menu is in the left pane of the Web Manager wi

4: Configuration Using Web Manager UDS2100 User Guide 23 Figure 4-2. Network Settings Automatic IP Address Configuration An IP address can be assi

4: Configuration Using Web Manager UDS2100 User Guide 24 4. When you are finished, click the OK button. 5. On the main menu, click Apply Settings

4: Configuration Using Web Manager UDS2100 User Guide 25 Server Configuration The unit’s server values display when you select Server from the main

4: Configuration Using Web Manager UDS2100 User Guide 26 Monitor Mode @ Bootup Select Disable to disable entry into the monitor mode using the yyy

4: Configuration Using Web Manager UDS2100 User Guide 27 Figure 4-4. Hostlist Settings 2. Enter or modify the following fields: Retry Settings R

4: Configuration Using Web Manager UDS2100 User Guide 28 Figure 4-5. Channel Serial Settings 2. In the available fields, enter the following inf

4: Configuration Using Web Manager UDS2100 User Guide 29 Stop Bits The stop bit follows the data and parity bits in serial communication. It indic

UDS2100 User Guide 3 Contents 1: Using This Guide 7 Purpose and Audience _______________________________________________ 7 Chapter Summary ________

4: Configuration Using Web Manager UDS2100 User Guide 30 Flush Output Buffer (Network to Serial) With Active Connect Select Yes to clear the outpu

4: Configuration Using Web Manager UDS2100 User Guide 31 2. In the available fields, enter or modify the following information: Connect Protocol

4: Configuration Using Web Manager UDS2100 User Guide 32 by default. Remote Port Enter the remote port number. Remote Host Enter the IP address o

4: Configuration Using Web Manager UDS2100 User Guide 33 3. When you are finished, click the OK button. 4. On the main menu, click Apply Settings

4: Configuration Using Web Manager UDS2100 User Guide 34 Accept Incoming Select Yes to accept incoming UDP datagrams. The default setting is Yes.

UDS2100 User Guide 35 55:: CCoonnffiigguurraattiioonn vviiaa TTeellnneett oorr SSeerriiaall PPoorrtt ((SSeettuupp MMooddee)) You must confi

5: Configuration via Telnet or Serial Port (Setup Mode) UDS2100 User Guide 36 To establish a Telnet connection: 1. From the Windows Start menu, cli

5: Configuration via Telnet or Serial Port (Setup Mode) UDS2100 User Guide 37 Exiting Setup Mode To exit setup mode: You have two options:  To s

UDS2100 User Guide 38 66:: SSeettuupp MMooddee:: SSeerrvveerr CCoonnffiigguurraattiioonn This chapter explains how to configure the network set

6: Setup Mode: Server Configuration UDS2100 User Guide 39 default setting is N (No), meaning the gateway address has not been set. To set the gatew

UDS2100 User Guide 4 Serial Port Connection ___________________________________________ 36 Exiting Setup Mode _____________________________________

6: Setup Mode: Server Configuration UDS2100 User Guide 40 There are three methods for assigning DHCP names to the unit.  Default DHCP Name: If yo

UDS2100 User Guide 41 77:: SSeettuupp MMooddee:: CChhaannnneell CCoonnffiigguurraattiioonn This chapter explains how to configure the serial po

7: Setup Mode: Channel Configuration UDS2100 User Guide 42 I/F (Interface) Mode The Interface (I/F) Mode is a bit-coded byte entered in hexadecimal

7: Setup Mode: Channel Configuration UDS2100 User Guide 43 Use the following table to select flow control options: Table 7-3. Flow Control Options

7: Setup Mode: Channel Configuration UDS2100 User Guide 44 Table 7-5. Connect Mode Options Connect Mode Option 7 6 5 4 3 2 1 0 a) Incoming

7: Setup Mode: Channel Configuration UDS2100 User Guide 45 a) Incoming Connection Never Accept Incoming Rejects all external connection attempts.

7: Setup Mode: Channel Configuration UDS2100 User Guide 46 If a partial IP address is presented in a command string, it is interpreted to be the l

7: Setup Mode: Channel Configuration UDS2100 User Guide 47 Figure 4-7. Hostlist Option To enable the hostlist: 1. Enter a Connect Mode of 0x20 (2

7: Setup Mode: Channel Configuration UDS2100 User Guide 48 e) Modem Mode In Modem (Emulation) Mode, the unit presents a modem interface to the atta

7: Setup Mode: Channel Configuration UDS2100 User Guide 49 Table 4-11. Modem Mode Messages Message Meaning Full Verbose OK Command was executed

UDS2100 User Guide 5 Disable TFTP Firmware Update ____________________________________ 58 Disable Port 77FE (Hex) _________________________________

7: Setup Mode: Channel Configuration UDS2100 User Guide 50 Table 7-6. Modem Mode Commands Modem Mode Command Function ATDTx.x.x.x,pppp or ATDTx.

7: Setup Mode: Channel Configuration UDS2100 User Guide 51 Remote IP Address This is the destination IP address used with an outgoing connection.

7: Setup Mode: Channel Configuration UDS2100 User Guide 52 (3) The TCP connection closes even if the remote site does not acknowledge the disconnec

7: Setup Mode: Channel Configuration UDS2100 User Guide 53 Note: All bit positions in the table that are blank represent “don’t care” bits for that

7: Setup Mode: Channel Configuration UDS2100 User Guide 54 DisConnTime (Inactivity Timeout) Use this parameter to set an inactivity timeout. The un

UDS2100 User Guide 55 88:: SSeettuupp MMooddee:: AAddvvaanncceedd SSeettttiinnggss Expert Settings (Option 5) Note: You can change these settin

8: Setup Mode: Advanced Settings UDS2100 User Guide 56 ARP Cache timeout in seconds Whenever the unit communicates with another device on the netwo

8: Setup Mode: Advanced Settings UDS2100 User Guide 57 Security Settings (Option 6) You can change security settings by means of Telnet or serial c

8: Setup Mode: Advanced Settings UDS2100 User Guide 58 Disable TFTP Firmware Update This setting defaults to the N (No) option. The Y (Yes) option

8: Setup Mode: Advanced Settings UDS2100 User Guide 59 Default Settings (Option 7) Select 7 to reset the unit’s Channel 1 configuration and expert

UDS2100 User Guide 6 D: Compliance and Disclaimer 81 Index 83 Figures Figure 2-1. Serial Tunneling Example _____________________________________

8: Setup Mode: Advanced Settings UDS2100 User Guide 60 Disable Web Setup No Disable ECHO ports Yes Enable Enhanced Password No

UDS2100 User Guide 61 99:: FFiirrmmwwaarree UUppggrraaddeess Obtaining Firmware You can obtain the most up-to-date firmware and release notes for

9: Firmware Upgrades UDS2100 User Guide 62 Figure 9-1. TFTP Window After the firmware has been loaded and stored, which takes approximately 8 seco

9: Firmware Upgrades UDS2100 User Guide 63 5. For Device Model, be sure the appropriate device (e.g., UDS2100) displays. 6. For Firmware File, cli

UDS2100 User Guide 64 1100:: MMoonniittoorr MMooddee Monitor Mode is a command-line interface used for diagnostic purposes. There are two ways to

10: Monitor Mode UDS2100 User Guide 65 Table 10-1. Monitor Mode Commands Command Command Name Function VS x.x.x.x Version Queries software head

UDS2100 User Guide 66 1111:: TTrroouubblleesshhoooottiinngg aanndd CCoonnttaacctt IInnffoorrmmaattiioonn This chapter discusses how you can di

11: Troubleshooting and Contact Information UDS2100 User Guide 67 Figure 11-1. Diagnostic, Power, and Serial Port LEDs Table 11-1. UDS2100 LEDs

11: Troubleshooting and Contact Information UDS2100 User Guide 68 Problems and Error Messages Table 11-2. Problems and Error Messages Problem/Messa

11: Troubleshooting and Contact Information UDS2100 User Guide 69 Problem/Message Reason Solution When you try to assign an IP with DeviceInst

UDS2100 User Guide 7 11:: UUssiinngg TThhiiss GGuuiiddee Purpose and Audience This guide provides the information needed to configure, use, and

11: Troubleshooting and Contact Information UDS2100 User Guide 70 Problem/Message Reason Solution The device server appears to be set up corre

UDS2100 User Guide 71 1122:: CCoonnnneeccttiioonnss aanndd PPiinnoouuttss UDS2100 Serial Ports The UDS2100 has two male DB9 DTE serial ports tha

12: Connections and Pinouts UDS2100 User Guide 72 Network Port The unit's back panel contains a 9-30VDC power plug and an RJ45 (10/100) Ethern

UDS2100 User Guide 73 1133:: TTeecchhnniiccaall SSppeecciiffiiccaattiioonnss Table 13-1. UDS2100 Technical Specifications Category Description C

13: Technical Specifications UDS2100 User Guide 74 Category Description Installable Industrial Protocols ModBus TCP, ModBus ASCII/RTU, DF1 Multi-M

13: Technical Specifications UDS2100 User Guide 75 Category Description transient over voltages Ethernet Port: 1500 VAC isolation shielded with sh

UDS2100 User Guide 76 AA:: AAlltteerrnnaattiivvee WWaayyss ttoo AAssssiiggnn aann IIPP AAddddrreessss Earlier chapters describe how to ass

A: Alternative Ways to Assign an IP Address UDS2100 User Guide 77 BOOTP Similar to DHCP, but for smaller networks. Automatically assigns the IP add

UDS2100 User Guide 78 BB:: BBiinnaarryy ttoo HHeexxaaddeecciimmaall CCoonnvveerrssiioonnss Many of the unit’s configuration procedures require

B: Binary to Hexadecimal Conversions UDS2100 User Guide 79 Scientific Calculator Another simple way to convert binary to hexadecimals is to use a s

1: Using This Guide UDS2100 User Guide 8 Chapter Description 13: Technical Specifications Lists technical specifications for the UDS. A: Alternati

UDS2100 User Guide 80 CC:: WWaarrrraannttyy Lantronix warrants each Lantronix product to be free from defects in material and workmanship for a pe

UDS2100 User Guide 81 DD:: CCoommpplliiaannccee aanndd DDiissccllaaiimmeerr Manufacturer’s Name & Address Lantronix 15353 Barranca Parkway,

D:Compliance and Disclaimer UDS2100 User Guide 82 Disclaimer and Supplementary Information This product has been designed to comply with the limits

UDS2100 User Guide 83 Index Applications, 9 ARP and Telnet, 77 AutoIP, 15, 76 Binary to hexadecimal conversions, 78 BOOTP, 15, 77 Channel settings,

UDS2100 User Guide 9 22:: IInnttrroodduuccttiioonn The UDS2100 is a 2-port device server that provides a quick, simple, and cost-effective way to